Excellent & Simple Battery Charger (Gel/Lead Acid/Li-Ion/+ more)



This circuit has been in use for 24 hours a day over the past 4-6 months. It operates perfectly. I used this circuit to charge two 18650 Li-Ion batteries for my cordless vacuum cleaner. You can charge many different battery types with this circuit. If you charge (2) Li-Ion batteries in series as I did, be sure to affix a 3A/ 70-90 degree Celsius thermal fuse between both batteries using thermal heatsink compound and foil tape. The fuse will then be wired in series with the 2 batteries. Also set charger output voltage to 8.33V – 8.36V, and use a 1 ohm resistor in the circuit.

Schematic here:

http://www.talkingelectronics.com/projects/200TrCcts/101-200TrCcts.html#84B

Thanks For Watching!

***If you enjoy watching my videos, please show your support by SUBSCRIBING, POSTING LINKS to my videos on other websites & blogs, rating a “THUMBS UP”, and watching my video playlists. Doing so helps to ensure that many more videos will be released in the future. (Views are essential to ensure this channel remains in an active state)***

admin

9V Alkaline Battery Charging Circuit(Also 1.5v Cells)



Learn how to make a good alkaline battery charger which is NOT likely to cause the batteries to leak or bulge, and will charge them properly. Though alkaline batteries are not intended to be recharged, they do seem to recharge well using this circuit. I put together this circuit from information obtained from the web page below. The circuit shown in the video was designed for 9V batteries, but you can also charge 1.5V (AA/AAA/AAAA)batteries by lowering the power supply voltage. The batteries are charged using low current DC pulses.

http://en.wikipedia.org/wiki/Recharging_alkaline_batteries

Schematic is here:

http://tinypic.com/m/k0oya1/4

For fully charged 9V LED indicator circuit:

http://tinypic.com/m/k0oydz/4

Thanks For Watching! Please SHARE with others, rate THUMBS UP, and SUBSCRIBE.

admin

Bedini SSG Battery Charger/Desulfator



This circuit uses a 12v battery to charge other 12v batteries to a higher voltage. According to John Bedini, you are getting more out of the circuit than you put into it(Which I have not proven). The high voltage that is created to charge the 12v battery is created by the back EMF from the coil.

Circuit/Schematic located here:

http://rpmgt.org/JoinBediniList.htm

Thanks For Watching!

***If you enjoy watching my videos, please show your support by SUBSCRIBING, POSTING LINKS to my videos on other websites & blogs, rating a “THUMBS UP”, and watching my video playlists. Doing so helps to ensure that many more videos will be released in the future. (Views are essential to ensure this channel remains in an active state)***

admin

Inductive Battery Charging Circuit (NiMH/NiCd)



Learn how to make a simple inductive battery charger for your NiMH/NiCd rechargeable batteries(2 to 4). The circuit in the video is for charging (2) batteries in series. This circuit operates in a very similar way as an ultrasonic toothbrush charger. The charging rate is slow(25-30mA), which can be made higher if desired, but it does charge well. The toothbrush charger uses a PWM IC to produce the high frequency pulses (75khz) into the primary winding with feedback to adjust the output under load, and this circuit uses a 555 IC to produce 42-46khz pulses into the primary winding to simplify the circuit. The transformerless power supply shown in this video is designed to power the exact circuit shown in this video. If you modify the primary winding and the circuit draws more current, then you will have to modify the transformerless power supply to deliver more current. You can also power the circuit using a very small 12V transformer. Don’t be afraid to experiment with different coils/windings!

**To support this channel, please share these videos with others, post links to this video as well as my other videos on other websites and blogs, and SUBSCRIBE.**

Thank You For Watching!

Link to Charger Schematic:

http://tinypic.com/m/k0oydw/4

Link to Transformerless Power Supply:

http://tinypic.com/m/k0oydv/4

admin

The Best Portable Battery I’ve Used Yet – Chargetech 54,000mAh BEAST!



The Best Portable Battery I’ve Used Yet – Chargetech 54,000mAh BEAST!
Buy it here,
https://amzn.to/2uDrnGt

TAKE THE WALL OUTLET ANYWHERE – The ultimate portable battery pack. PLUG is a power supply and mini generator. It’s compact size, universal compatibility, high capacity and solar recharge capability (sold seperately) means you can enjoy and charge and provide power to your products anywhere. The PLUG weighs 2lbs 3oz with dimensions of 5.6in x 1.6in x 8.6in
PASS THROUGH CHARGING TECHNOLOGY – Pass through charging technology allows you to charge your devices while the battery pack itself is charging. The portable ac battery pack can be used just like you would use a USB hub or surge protector. Add a solar panel charger and take your electronics into the great outdoors and off the grid
POWER YOUR LAPTOP AND CPAP – This battery pack works with all devices up to 250 watts. Power your laptop, CPAP, tablets, phones and other household devices.
UNIVERSAL COMPATIBILITY – This portable charger contains 2 fast charge USB port, 2 AC wall outlets and a USB type C outlet. Battery pack is compatible with electronic devices including mobile devices (Apple, Samsung, Google, Android), Laptops (Apple, Dell, Toshiba, Asus, HP), lights, television, stereos, IPhone, iPad, CPAP machines, medical devices, printers, flat screen TVs, PS4, Xbox One, Wii U, drones. Check the device is compatible with the 250 watt surge protector rating
QUICK CHARGE, HIGH CAPACITY INTERNATIONAL DESIGN – The device has a quick charge high capacity design that quickly charges and powers your electronic devices. It’s 54k mAh capacity is built with 16x 3,000 mAh Panasonic battery cells. The international outlets are compatible with Type A, B, C, I, G, E, and L

Join the Notification Squad: http://notificationsquad.net
Wanna buy some of my gadgets – http://amzn.to/1zZ2y4P
Want a T-Shirt – http://www.flossycarterstore.com
Find me Online,
http://instagram.com/flossy_carter
https://plus.google.com/+FlossyCarterGoogleGangsta/posts
https://www.facebook.com/FlossyCarter

Payments: paypal.me/Flossycarter

admin

Homemade 6V / 2.5 Amp Power Supply/Battery Charger



If your looking for a HIGHLY efficient (6VDC 2.5A / 6VAC 3.0A) power supply or 6V lead acid battery charger, then look no further. This power supply/charger is made using a 120V (MOT) microwave oven transformer, by performing the modifications shown in this video. 120V transformer current at idle(NO LOAD) only draws 30mA, and using a full 2.5A load, 200mA. NO heating issues of the core whatsoever. As usual, always be very careful when working with 120VAC/240VAC projects!

Thanks For Watching!

***If you enjoy watching my videos, please show your support by SUBSCRIBING, POSTING LINKS to my videos on other websites & blogs, rating a “THUMBS UP”, and watching my video playlists. Doing so helps to ensure that many more videos will be released in the future. (Views are essential to ensure this channel remains in an active state)***

admin

Cut-Off Circuit For 12V Lead Acid Battery Charging



If you are looking for a simple but effective Lead Acid battery charger cut-off circuit, then look no further. You can use this circuit in conjunction with any battery charger(except capacitive types) which do not have an automatic shut-off once the battery voltage has climbed to 14.2V(You can adjust this value with the zeners). You can modify the circuit to charge 6V lead acid batteries instead of 12V as shown in this video. Just replace the relay coil with a 6V type, use a lower voltage power supply (8-12VDC Open Circuit), replace the 12v zener leading to the base of the NPN with a 6V or 6.2V, along with the same (2) 1n4001’s in series, replace the 12V zener to the relay coil with a 6/6.2V zener, and cut the value of the LED resistor in half.

Link To Schematic:

http://tinypic.com/m/k0oy06/4

Thanks For Watching!

***If you enjoy watching my videos, please show your support by SUBSCRIBING, POSTING LINKS to my videos on other websites & blogs, rating a “THUMBS UP”, and watching my video playlists. Doing so helps to ensure that many more videos will be released in the future. (Views are essential to ensure this channel remains in an active state)***

admin